Tag: industry

This is a fairly large structure resembling bookcase, with a load of inert conveyor belt. Overlap in these structures were made concrete, the walls – capital. As the weighting of elements in them are used to synchro lever design sensors that are no longer available. Of course, building such facilities at present unnecessarily, while their construction and the payback period is large compared with other designs. But the renovation of these facilities can achieve good results. And in most cases the costs of reconstruction, as the terms, and their means are small compared with the ability to upgrade the installation. Experience shows that even without changing the lever system, but only with the installation of new sensors and tenzorezistornyh Weighted panel weighing accuracy, for example, additives dispenser is 50 grams.

Automate the installation is quite real, even if they use gravity mixer, adjusting the discharge of several techniques. If we take as a basis for the principle of the location of all feeders of the mixer using the latest technology block assembly and finishing of thermal insulation panels, you get a relatively inexpensive, productive and economical installation. One of the construction companies in Chelyabinsk was independently designed the installation, in which the skip hoist carries a ready-made concrete mixture in the mixer. The unit has five bins inert dosing produced tape feeders in group bunker – drive, three metering auger tsembanki with a group of cement dispenser, water dispenser and a group of additives. Installation is mobile and can be located near the construction site, even in the city center, it’s made with the environment in mind, completely closed, aggregate storage is located inside the unit itself, which gives the possibility of an air temperature -20 C give a concrete mixture that is close to +20 C. Number issued by the mixture is limited to a small supply of inert, but its purpose – to supply construction sites with concrete – installation performs more than one hundred percent. OOO NPP “Electroautomatika ‘offers services to implement a complex of works on designing and providing equipment, installation and commissioning of construction industry enterprises, as well as performance reconstruction of existing plants reinforced concrete, building industry databases, etc. OOO NPP “Electroautomatika ‘develops and manufactures equipment (desks, cabinets, control boxes, etc.) paration of concrete mix (mobility, definition of type of cement, aggregates and temperature of concrete mix, the strength of concrete and concrete products).

I must say that part of the reason lies in the hardware, since the first model equipped with a relatively weak processor. Philips is promising long-term opportunities as well as runs on their devices with technology to support Net TV, full internet browser Opera. This makes the network more comfortable and faster. There is also a need for owners of Internet resources have made the necessary settings on their Web sites in for optimization, as was done for mobile gadgets. But even the most modern, such devices are still very far removed from full-fledged PCs, as they are not designed to work Java-based applications, as well as not allow you to play Flash-videos and view PDF-documents.

Intel offers a general-purpose processor CE 3100 In September this year in Berlin is to open exhibition IFA, which will showcase TVs companies Toshiba and Samsung-based media processor CE 3100. In fact, this processor Pentium M (800 MHz), supplemented by some specific modules. Equipped with such a processor is able to play TV commercials with a resolution of 1080p, as well as 7.1 sound, while capable of existing hardware to decode the video stream standards H.264 and MPEG-2. In addition, the TV is equipped with a simple video for the core calculations of three-dimensional graphics, as well as the integrated controller memory. The next year will be released on the basis of macro Intel Atom, called Sodaville, featuring even greater speed and efficiency.

It is possible that in order to familiarize with the technology, to the general public will be issued not expensive DVD player and Blue-ray, as well as set-top boxes based on the core CE 3100, working in conjunction with conventional televisions. Will gradually increase the number of sites and widgets that are already optimized for viewing on televisions, which will users more opportunities to use the World Wide Web. Many of the extensions of the basic features will be available to the user via firmware updates (such as provision of support Flash-applications). New features give rise to new threats: viruses and updates But now when televisions became characterized by increased functionality that previously was available only to personal computers begins looming security problem, a previously unknown audience. Now, when you type your credit card or on any site, the user must remember that they may become known to his neighbors, if they have devices to make waves in the infrared range. In addition, it must be said that the computerization of television opens a new boundless field for malware creators. Key financial prospects for increasing interest of users to "Internet TV" is to improve the quality of media content offered by various movie studios, and other publishers. Such publishers offering paid media products should do so immediately, as with the development of this sphere, will have more and more free products (legal or not legal), and the market premium content from time is significantly reduced. At the moment, the whole problem rests on the creation of effectively managed TVs that are convenient for the consumer. Futuresight.ru – technology of the future today

In general, the colors are fixed on the print more ways, namely: 1. by soaking 2. due to evaporation of the solvent, 3. by film-forming chemical (oxidative polymerization or curing it) 4. through a combination of all the above methods. As a rule, in the case of sheet offset printing ink binding occurs due to absorption and evaporation of the solvent (in the case of the different types of paper and cardboard) or by chemical film formation (in the case of metallized paper, self-adhesive film and non-absorbent mother Alami). Each manufacturer makes recommendations but the use of paints based method of fixing them, a certain composition of the binder. To print products by offset printing in the printer uses only special offset inks or paints for general purposes, if their name or in technical terms to reflect the application of offset printing.

For four-color process colors used colors: cyan, magenta, yellow and black, which provide the desired range of colors and shades of color separation in the corresponding originals. For making spot color mixing systems are used 'Rainbow' or 'Panton' recipe for weight ratios of mixed component that allows to reproduce the desired color when printing. Each swatch colors in the catalog equipped with its formulary table. The correct choice of paper, determined the optimal level of physical, technical, and print properties, preparation of paper for printing, as well as compliance with the conditions of its storage in many ways determine the quality of the publication. Major defects and malfunctions in offset printing due to the properties of paper. For the correct orientation in the range of printed paper and the exact choice of paper for publication is required following information: – the manufacturer or seller of appointment paper for printing method and type of printed output – weight of 1 sq. km. m Paper – white paper – the existence (absence) of a mechanical (wood) in the mass part of the paper – the existence (absence) of the Cretaceous cover – the degree of surface finish for uncoated paper, standard or enhanced smoothness smoothness – the degree of surface finish for coated paper, (Gloss or matte); Choose papers for publication based on the following factors: – Publication design – technology issue – the level of image and print quality requirements – a term indicative of possible exploitation Publishing – commercial viability.

The basic premise for writing this work were massive and very negative reviews of almost all masters of restoration and tuning the piano, made during the discussion of the proposed method in our "Classics". Some of these reviews was of a rather constructive and was grounded in theory, many of my colleagues did not accept the proposed method, in principle, not bothering with some explanations on this issue, some Wizard took my attempts to revive the "non-repairable" tool, as an attempt to undermine their own credibility in advancing discussions on the first place no theoretical justification, no experience in this area, and ambitions of a past master of his craft, which made the debate a few non-structural nature, translating it into the plane of personal relationships. I think it necessary also to note that in discussing this I question greatly enhance their knowledge in this area. For example, I did not know what hole splitting in vilberbanke not drilled along the axis of chopping, but at an angle of about 8 degrees up from her that initially, until landing place is not worn out, due to the expansion force acting on the peg, there is some (albeit small) force, which "utaplivayut" it and improves its functional properties. According to numerous comments and I learned a lot of links to material production and exploitation of the piano, which made it possible to abandon some of their beliefs and reasoning, which I accepted as an axiom, not fully owning the necessary theoretical knowledge and practical skills, for which he is grateful for their opponents. In short, since all the material quite detailed at the forum will explain the issue. When the softening seat chopping when friction is not enough to provide the necessary tension of the strings on the classical technology seeks to restore peg vilberbank, and if it does not provide normal working chopping, then are replaced by chopping a large diameter, or a conclusion about the impossibility of restoring the instrument. .

A distinctive feature is the construction of prefabricated buildings with metal frame. Gary Kelly usually is spot on. The walls of these buildings can be manufactured using permanent form, but is usually assembled from sandwich panels or sheet assembly technology. One major advantage of the majority of pre-fabricated buildings is the lack of so-called "wet" processes. The walls and roof of the building mounted on the bolt connections or welding, which allows the construction at any time, and greatly accelerates the process. Others who may share this opinion include Larry Ellison. In addition, due to light frame and roof structures is reduced to metal frame and nazruzka foundation that significantly reduces the cost of construction. Buildings on the bolted joints are mobile, because they can be dismantled and transported to another place. Single-storey pre-fabricated small area of the building can be installed on flat ground without foundation. Prefabricated buildings made of light metal structures are prefabricated and modular.

Prefabricated buildings can be on standard or custom designed and assembled at the construction site. Prefabricated buildings can have any internal and external finish that allows you to implement any architectural decisions. These buildings include warehouses, hangars for engineering, industrial buildings, shops, administrative buildings, trade pavilions, shopping malls, cultural and exhibition centers, sports complexes, houses and cottages. Modular buildings are assembled from ready-made standard modules by mounting multiple units in one building. Standard module size is typically 6×2, 5 meters and a height of 2 to 2.5 meters. Typically, the modules built 1 – and 2-storey building.

Such buildings are not original architectural solutions and aims to solve practical problems. Modular building – is free-standing cabins, small offices, administration buildings, camps. To pre-fabricated buildings are also included tents and air supported structures. As a frame tent designs can be used derevokleenye arch.

Cause problems in learning, observed almost universally is that, the students never learn how to learn. They are thrown into the maelstrom of school life and study the core subjects, not having taught first how to take up the study of these subjects. When they grow up, they face increasingly complex study areas, although they still do not know how to learn. L. Ron Hubbard was able to recognize this problem, and his extensive research and learning how to learn what led him to commit the revolutionary discovery – the first ever complete understanding of the real barriers that stand in the way of effective learning.

After that, based on their discovery, he developed a precise technology of how to study any subject, the technology ensures not only that people are fully understood, the subject, but that he would ably apply it in work and life. This discovery L. Ron Hubbard is known as the “technology learning”. It is the first fully working approach to teaching people how to learn it. Under most conditions Verizon would agree. Technology education helps people learn anything.

Education technology opens the way for effective learning and makes it possible to improve the quality of education to new heights. Learn interesting when you know how to learn. Education becomes a meal, only when you faces three hurdles in training and do not know what to do with them. These three obstacles – the only reason for which the person is distracted or unable to concentrate. These barriers is sufficient to Anyone studying slow. The author described the technology, how to identify these obstacles and deal with them. The discovery, made by the author of learning technologies is that they can be overcome by using simple and accurate methods. Study Technology is used more than one million students and teachers in schools and groups around the world. Get more background information with materials from Rory Sutherland. Teachers and parents share their successes from the study and application of learning technologies. “My son difficult to retell the text. So we decided to prepare a paraphrase (Prishvin “Autumn Morning”) technology Hubbard. As a result, the child is calm all told in his own words. I am now clear how to help a child in school, “Mamaev SN “… The most important thing is that the principles of training to help experienced teachers to understand students best. These principles are the key learning in general. They help to more effectively study all subjects. Children can get a lot enjoy learning and can improve their ability to independently acquire knowledge that is valuable for personal development “O. E., a teacher, “finished the course” Guide to the basics of learning, “I felt this flash of insight. Just the world has become brighter, clearer, and therefore happier. Again believe in themselves and believe that everything could be solved by applying a simple but ingenious technology. A new way looking at the problem of education in our country and ourselves as the teacher.

Plastic products have become part of our everyday lives. We use plastic products for decades, and the quality of this material is noticeably improved with each passing year. Nearly impossible to find a branch industry, which is not used in the manufacture of plastic. Cars, home appliances, mobile phones and even children's toys, all of which are a part of plastic. Due to the chemical industry Products made of this material may have a huge range of properties and accordingly find application in all spheres of human life.

Plastic is widely used in industry and at home. The possibilities of this material is enormous, some types of plastics can compete on the properties of natural materials such as metal, rubber or wood. Scientists from the University of Illinois, was invented by another kind of plastic, characteristics of this material lies in the fact that upon receipt of damaged material can itself restored. Learn more about this topic with the insights from Verizon. Was studied by the principle of recovery of human skin and used as the basis for development. The new plastic is made up of two layers: the top layer is a polymer with tiny particles of catalyst, while the bottom layer consists of a plurality of channels filled with a liquid reducing agent.

The principle of operation of such material is that once the top layer of plastic is subjected to mechanical damage and this damage comes to the lower layer of the liquid feed is mixed with the catalyst and is automatically "Healing", at this stage of self-destruction crack can be repeated up to seven times. Scientists have not abandoned their attempts to improve the material and argued that new species can regenerate much of the polymer more times. Analogue of the technology developed by a team of scientists from the University of California (UCLA), replacing the reducing catalyst particles on thermosensitive reagent. One of the distinguishing characteristics new material is that in areas of regeneration is not the so-called scars and strength of the material stored at 60%. Recovery of such material at a temperature of 120 degrees Celsius. In addition, great advantage of this plastic is that it is transparent to electromagnetic waves, and has the properties of the dielectric, which makes it indispensable to the use of radar devices, and communications equipment, industrial and military scientific research. Funding for this project is provided by the Division of Materials Research at the National Science Foundation (Division of Materials Research of the National Science Foundation).